| . |
| |
|
|
| ACOUSTICAL |
|
|
| Operating frequency range |
70 Hz - 18 kHz |
 |
| Frequency response |
76 Hz - 16 kHz ±4 dB |
| Phase response |
1.5 kHz - 16 kHz ±30° |
| Maximum peak SPL |
131 dB |
| Dynamic range |
>110 dB |
| Acoustical crossover |
1100 Hz |
|
|
| Horizontal coverage |
100° |
| Vertical coverage |
Varies, depending on array length and configuration |
|
|
| TRANSDUCERS |
|
| Low/low-mid frequency |
Two 8” cone drivers with neodymium magnets |
|
Nominal impedance: 4 Ω |
|
Voice coil size: 1.5” |
|
Power handling capability: 600 W (AES); 900 W peak |
| High frequency |
3” compression driver |
|
Nominal impedance: 8 Ω |
|
Voice coil size: 3” |
|
Diaphragm size: 3” |
|
Exit size: 1.2” |
|
Power handling capability: 180 W (AES); 360 W peak9 |
|
|
| AUDIO INPUT |
|
| Type |
Differential, electronically balanced |
| Max. common mode range |
±15 V DC, clamped to earth for voltage transient protection |
| Connectors |
Female XLR input with male XLR loop output or VEAM all-in-one connector (integrates AC, audio, and network) |
| Input impedance |
10 kΩ differential between pins 2 and 3 |
|
| Wiring |
Pin 1: Chassis/earth through 220 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies |
|
|
Pin 2: Signal + |
|
|
Pin 3: Signal - |
|
|
Case: Earth ground and chassis |
|
| DC Blocking |
Differential DC blocking up to max common mode voltage |
|
| CMRR |
>50 dB, typically 80 dB (50 Hz – 500 Hz) |
|
| RF filter |
Common mode: 425 kHz |
|
|
Differential mode: 142 kHz |
|
| TIM filter |
<80 kHz, integral to signal processing |
|
| Nominal input sensitivity |
0 dB V (1 V rms, 1.4 V pk) continuous is typically the onset of limiting for noise and music. |
|
| Input level |
Audio source must be capable of producing +20 dBV (10 V rms, 14 V pk) into 600 Ω in order to produce maximum |
|
|
peak SPL over the operating bandwidth of the loudspeaker |
|
|
|
|
| AMPLIFIERS |
|
|
| Amplifier type |
Three-channel complementary MOSFET output stages (class AB/H) |
|
| Output power |
1275 W (three channels; 2 x 500 W, 1 x 275 W); 2550 W peak10 |
|
| THD, IM TIM |
< .02% |
|
| Load capacity |
4 Ω low and mid; 8 Ω high channels |
|
| Cooling |
Convection cooled |
|
|
|
|
|
|
|
| AC POWER |
|
|
| AC power connector |
PowerCon with looping output or VEAM all-in-one connector (integrates AC, audio and network) |
|
| Voltage selection |
Automatic, two ranges, each with high-low voltage tap (uninterrupted) |
|
| Safety agency rated operating voltage |
95 V AC – 125 V AC, 208 V AC - 235 V AC, 50/60 Hz |
|
| Turn on/turn off points |
85 V AC - 134 V AC; 165 V AC - 264 V AC |
|
| Idle current |
0.680 A rms (115 V AC), 0.360 A rms (230 V AC), 0.760 A rms (100 V AC) |
|
| Max. long-term continuous current (>10 sec) |
2.3 A rms (115 V AC); 1.2 A rms (230 V AC); 2.6 A rms (100 V AC)11 |
|
| Burst Current (<1 sec) |
4 A rms (115 V AC), 2 A rms (230 V AC), 4.5 A rms (100 V AC) |
|
| Ultimate Short-Term Peak Current Draw |
13 A pk (115 V AC), 6.5 A pk (230 V AC), 15 A pk (100 V AC) |
|
| Inrush Current |
10 A pk (115 and 100 V AC), 18 A pk (230 V AC) |
|
|
|
|
| RMS NETWORK |
|
|
|
Equipped with two-conductor twisted-pair network, reporting all operating parameters of amplifiers to system |
|
|
operator’s host computer. |
|
|
|
|
| PHYSICAL |
|
|
| Enclosure |
Premium birch plywood |
|
| Finish |
Black textured |
|
| Protective grille |
Powder-coated, hex-stamped steel, black mesh |
|
| Rigging |
QuickFly rigging with four captive GuideALinks in the bottom corners of two aluminum and steel end frames, |
|
|
secured with quick-release pins |
|
| Dimensions |
28.54 w x 9.19 h x 12.75 d (724.84 mm x 233.31 mm x 323.85 mm) |
|
| Weight |
62 lbs (28.12 kg) |
|
